Categories
Contact Us
- Phone+86 18859257178
- Emailsarui@saruimic.com
- AddressRoom 1603-3, No. 63, Xishanwei Road, Phase III, Torch High tech Zone, Xiamen
Previous
Next
90 Degree Curved 40x40 Aluminum Extrusion
Description
90 Degree Curved 40×40 Aluminum Extrusion
・Materials
[ M ] Material: A6N01SS-T5 Aluminum Alloy
[ S ] Surface Treatment: Anodize
90 Degree Curved 40×40 Aluminum Extrusion
Specifications
| Part Number | – | R |
| HFSMGQ8-4040 | – | R140 |
| Part Number | R | Slot Width | Mass kg | Sectional Area mm2 | Cross Sectional Moment of Inertia mm4 | |
| ℓx | ℓy | |||||
| HFSMGQ8-4040 | 140 | 10 | 1.2 | 640 | 10.4×104 | 10.4×104 |
90 Degree Curved 40×40 Aluminum Extrusion
Alterations
Alterations are not applicable to all frames.
| Category | Alteration Names | Codes | Explanations |
| Aluminum Frame Alteration Summary/Chamfer/Part# Labeling Service | |||
| End Tapping | End Tapping on Center Hole | LTP/RTP/TPW LHP/RHP/HPW |
Add tappings on frame ends. |
| End Tapping 4 Corner Holes | LSP/RSP/SPW | ||
| Specify How to Cut | Precision Cut | SC | Change total length tolerance. (Ｌ±0.5→Ｌ±0.2)
Available only for Ｌ≦1500 |
| 45 deg Cut | L_T45/R_T45 | Cut at 45 deg angle. | |
| Wrench Access Holes | Wrench Access Hole at Fixed Position | LWP/RWP | Add wrench access holes at fixed position for blind joints. |
| Wrench Access Hole at Specified Position | AH/BH/AV/BV | Add wrench access holes at specified position for blind joints. | |
| Counterbores | Counterbores at Specified Position | Z6/XA100 | Add counterbores at specified position. Use the holes for connecting the frames and a table top. |
| Holes for Specific Blind Joint Type | D Hole | LDH/RDH | Add holes needed for Single Joint connection. |
| S Hole | LSH/RSH | Add holes needed for pre-assembly double joint connection. | |
| M Hole | LMH/RMH | Add holes needed for post-assembly double joint connection. | |
| L Hole | JLP/KLP | Add holes needed for parallel joint connection. | |
| Other Alterations | GNFS/GFS Series End Tapping | LTS/RTS/TSW | Add end tappings on high rigidity frames. |
| HFSR Series End Tapping | LTS/RTS/TSW | Add end tappings needed for adding a protection cover on the end fo HFSR series frame. |
90 Degree Curved 40×40 Aluminum Extrusion
Basic Information
| Standard Extrusion Size(mm) | 40 | Extrusion Size | 40×40 | Extrusion Shape | Curved |
| Number of Extrusion Slots | 1 Slot-1 Slot | Extrusion Type | HFS (Standard) | Surface Finish | Clear Anodize |
| Number of Grooved Surfaces | Four Side Slots | Surface Milled | None | Material | A6N01SS-T5 Aluminum Alloy |
| Extrusion Size – Width (A)(mm)(mm) | 40 | Extrusion Size – Thickness (T)(mm)(mm) | 40 | L Dimension Fixed, Specified | Standard, Fixed |
| Extrusion Bending Radius R | 140 |
Experience
Our factory supply OEM service(custom service) in precision investment casting,which are also called lost wax casting, We have been committed to this technique for over 10 years . Our specialized engineer can provide you the full-service of technology advice and products improving projection,and also reduce the cost of the parts.
