Categories
Contact Us
- Phone+86 18859257178
- Emailsarui@saruimic.com
- AddressRoom 1603-3, No. 63, Xishanwei Road, Phase III, Torch High tech Zone, Xiamen
Previous
Next
8-45 Series45x90 Aluminum Extrusion
Description
8-45 Series45x90 Aluminum Extrusion
Specifications
| Part Number | – | L |
| HFS8-4590 | – | 800 |
■Configurable Length Extrusions
| Type | [ M ]Material | [ S ]Surface Treatment | Part Number | L 0.5mm Increment |
Mass kg/m |
Sectional Area mm2 | Cross Sectional Moment of Inertia mm4 | |
| ℓx | ℓy | |||||||
| HFS | A6N01SS-T5 Aluminum Alloy | Clear Anodize | HFS8-4590 | 50~4000 | 4.14 | 1534 | 32.29×104 | 124.7×104 |
| HFS | A6N01SS-T5 Aluminum Alloy | Black Anodize | HFSB8-4590 | 50~4000 | 4.14 | 1534 | 32.29×104 | 124.7×104 |
| HFSL | A6N01SS-T5 Aluminum Alloy | Clear Anodize | HFSL8-4590 | 50~4000 | 2.98 | 1101 | 22.87×104 | 87.16×104 |
| GFS | 6061-T6 Aluminum Alloy Equivalent | Clear Anodize | GFS8-4590 | 50~4000 | 5.22 | 1935 | 42.99×104 | 163.4×104 |
[ ! ]Applicable to 6000mm depending on products.
8-45 Series45x90 Aluminum Extrusion
Alterations
Alterations are not applicable to all frames.
| Category | Alteration Names | Codes | Explanations |
| Aluminum Frame Alteration Summary/Chamfer/Part# Labeling Service | |||
| End Tapping | End Tapping on Center Hole | LTP/RTP/TPW LHP/RHP/HPW |
Add tappings on frame ends. |
| End Tapping 4 Corner Holes | LSP/RSP/SPW | ||
| Specify How to Cut | Precision Cut | SC | Change total length tolerance. (Ｌ±0.5→Ｌ±0.2)
Available only for Ｌ≦1500 |
| 45 deg Cut | L_T45/R_T45 | Cut at 45 deg angle. | |
| Wrench Access Holes | Wrench Access Hole at Fixed Position | LWP/RWP | Add wrench access holes at fixed position for blind joints. |
| Wrench Access Hole at Specified Position | AH/BH/AV/BV | Add wrench access holes at specified position for blind joints. | |
| Counterbores | Counterbores at Specified Position | Z6/XA100 | Add counterbores at specified position. Use the holes for connecting the frames and a table top. |
| Holes for Specific Blind Joint Type | D Hole | LDH/RDH | Add holes needed for Single Joint connection. |
| S Hole | LSH/RSH | Add holes needed for pre-assembly double joint connection. | |
| M Hole | LMH/RMH | Add holes needed for post-assembly double joint connection. | |
| L Hole | JLP/KLP | Add holes needed for parallel joint connection. | |
| Other Alterations | GNFS/GFS Series End Tapping | LTS/RTS/TSW | Add end tappings on high rigidity frames. |
| HFSR Series End Tapping | LTS/RTS/TSW | Add end tappings needed for adding a protection cover on the end fo HFSR series frame. |
8-45 Series45x90 Aluminum Extrusion
Basic Information
| Standard Extrusion Size(mm) | 45 | Extrusion Size | 45×90 | Extrusion Shape | Rectangle |
| Number of Extrusion Slots | 1 Slot-2 Slots | Number of Grooved Surfaces | Four Side Slots | Surface Milled | None |
| Extrusion Size – Width (A)(mm)(mm) | 45 | Extrusion Size – Thickness (T)(mm)(mm) | 90 |
